Introduction and Planning Guide

Options

The IBM 2212 ships with unpopulated adapter slots. You can customize it to meet your needs with the PMC and CPCI adapters listed in this section.

With one CPCI adapter slot each, Models 10F, 15F, 10H, and 15H are suited for well-defined connectivity opportunities requiring only one CPCI adapter.

With four CPCI adapter slots each, Models 40F, 45F, 40H, and 45H offer scalable support for your network as it expands.

You can order the following adapters for the IBM 2212:

Adapter	Feature Code	Part Number	Page
PMC adapter options
1-Port Token-Ring PMC	3101	85H4721	"1-Port Token-Ring PMC Adapter (FC 3101, PN 85H4721)"
1-Port 10/100 Ethernet PMC	3102	85H4722	"1-Port 10/100-Mbps Ethernet PMC Adapter (FC 3102, PN 85H4722)"

If you have a standard system card you can also order the following additional options for the IBM 2212:

32-MB DRAM SIMM (FC 3132, PN 85H4408)
64-MB DRAM SIMM (FC 3133, PN 85H4409)
Hard drive (FC 3130, PN 85H4715) to make a compact flash model into a hard drive model

If you have a high-performance system card you can also order the following additional options for the IBM 2212:

64-MB EDO DRAM DIMM (FC 3233, PN 44L2537)
128-MB EDO DRAM DIMM (FC 3234, PN 44L2539)
256-MB EDO DRAM DIMM (FC 3235, PN 44L2541)
Hard drive (FC 3130, PN 85H4715) to make a compact flash model into a hard drive model

Note:

The IBM 2212 allows a hard drive or compact flash option; not both.

1-Port Token-Ring PMC Adapter (FC 3101, PN 85H4721)

Provides for one attachment to a 4- or 16-Mbps Token-Ring LAN wired with 100-ohm twisted-pair cable using RJ-45 connectors. For attachment to 150-ohm wiring systems, an impedance converter such as IBM PN 73G8315 must be used. Cable FC 2391 (PN 41H9082) is available for this adapter.

This adapter plugs into the PMC adapter slot on the system card.
Note: Total cable length to the attaching device is limited to 100 m (328 ft) and is for indoor use, only.

1-Port 10/100-Mbps Ethernet PMC Adapter (FC 3102, PN 85H4722)

Provides one port for 10/100-Mbps Ethernet connections using an RJ-45 connector. This attachment provides:

2-KB entry hardware Transparent Bridging
IEEE 802.3 10-Mbps Ethernet
IEEE 802.3u 100-Mbps Ethernet

It plugs into the PMC adapter slot on the system card. Cable FC 2391 (PN 41H9082) is available for this adapter.

4-Port WAN CPCI Adapter (FC 3103, PN 85H8836)

Each port of the 4-port WAN CPCI adapter, 4-port WAN PMC adapter, and integrated WAN ports supports any of the following interfaces and speeds and complies with the respective interface standard:

EIA 232D/V.24: 2400 bps to 115.2 Kbps
V.35: 9600 bps to 6.312 Mbps is supported with external clocking⁵ and 9600 bps to 2.048 Mbps is supported with internal clocking.
V.36: 9600 bps to 6.312 Mbps is supported with external clocking⁵ and 9600 bps to 2.048 Mbps is supported with internal clocking.
X.21: 2400 bps to 6.312 Mbps is supported with external clocking⁵ and 2400 bps to 2.048 Mbps is supported with internal clocking.

The optional CPCI adapter, the integrated WAN ports on the IBM 2212 standard system card, and the 4-port WAN PMC adapter for the high-performance system card support the 8 cables listed under "WAN cables" in Cables.

The optional adapter plugs into any 3U CPCI adapter slot. (For more information about CPCI dimensions, see CPCI Adapter Specifications).

2-Port ISDN BRI-U CPCI Adapter (FC 3104, PN 85H4725)

Provides a 2-wire U interface per port for North America. Uses an RJ-45 connector. Support for cable FC 2391 (PN 41H9082).

This adapter plugs into any 3U CPCI adapter slot.

2-Port ISDN BRI-S/T CPCI Adapter (FC 3105, PN 85H4726)

Provides a 4-wire S/T interface per port. Uses an RJ-45 connector.

This adapter requires cable FC 2391 (PN 41H9082), except in Australia, where it requires cable FC 2318 (PN 86H0774).
Note: Requires an external network termination (NT-1) for connections in North America.

This adapter plugs into any 3U CPCI adapter slot.

1-Port ISDN PRI (T1/J1) CPCI Adapter (FC 3106, PN 85H4727)

Provides one attachment to an ISDN Primary Rate service at T1/J1 speed.
Note: This can also be used for channelized or fractional T1/J1 support.

This attachment provides:

Support for T1/J1 line speed of 1.544 Mbps.
Twenty-three 64-Kbps B-channels for data and one 64-Kbps D-channel for signaling, or twenty-four 64-Kbps time slots (24 DS0s) for channelized service.
Selectable framing to D4 (SF) format.
Detection and generation of yellow and blue alarms.
Facility Data Link (FDL) support.
Generation of DSX-1 and CSU line build outs.
Generation and detection of CSU loop codes.
Line error counters for BPV, CV, CRC6, and framing-bit errors.
Monitoring and enforcing of ANSI ones density requirement.
B8ZI and AMI line coding.
RJ-45 female connector.
Support for cables FC 2391 (PN 41H9082) and for Japan FC 2323 (PN 30L6523).
Two separate loopbacks for testing: payload and line. The diagnostics program provides a local loopback, as well.

This adapter plugs into any 3U CPCI adapter slot.

1-Port ISDN PRI (E1) CPCI Adapter (FC 3107, PN 85H4728)

Note:

This can also be used for channelized E1.

Provides one attachment to an ISDN Primary Rate service at E1 speed. This attachment provides:

Support for E1 line speed of 2.048 Mbps.
Thirty 64-Kbps B-channels for data and one 64-Kbps D-channel for signaling or thirty-one 64-Kbps time slots (31 DSOs) for channelized service.
Selectable framing to FAS and CRC4 formats.
Detection and generation of remote and AIS alarms.
Generation of line build outs for a 120-ohm line.
Two separate loopbacks for testing: payload and line. The diagnostics program provides a local loopback, as well.
Line error counters for bipolar and code violations, CRC4 code word errors, FAS errors, and E-bits.
B8ZI, AMI, and HDB3 line encoding.
RJ-45 female connector.
Support for cable FC 2324 (PN 30L6524) and in Australia for FC 2325 (PN 30L6529).

This adapter plugs into any 3U CPCI adapter slot.

2-Port ISDN PRI T1/J1 CPCI Adapter (FC 3108, PN 85H4680)

Provides two ports to an ISDN Primary Rate or channelized service at T1 speed. This attachment provides the same functions as "1-Port ISDN PRI (T1/J1) CPCI Adapter (FC 3106, PN 85H4727)". It supports cables FC 2391 (PN 41H9082) and, for Japan, FC 2323 (PN 30L6523).

This adapter plugs into any 3U CPCI adapter slot.

2-Port ISDN PRI E1 CPCI Adapter (FC 3109, PN 85H4682)

Provides two ports to an ISDN Primary Rate or channelized service at E1 speed. This attachment provides the same functions as "1-Port ISDN PRI (E1) CPCI Adapter (FC 3107, PN 85H4728)". It supports cables FC 2324 (PN 30L6524) and, for Australia, FC 2325 (PN 30L6529).

This adapter plugs into any 3U CPCI adapter slot.

2-Port Token-Ring CPCI Adapter (FC 3110, PN 85H4717)

Provides for two attachments to 4- or 16- Mbps Token-Ring LANs wired with 100-ohm unshielded twisted-pair cable using RJ-45 connectors. For attachment to 150-ohm Token-Ring wiring systems, an impedance converter such as IBM PN 73G8315 must be used.

This adapter plugs into any 3U CPCI adapter slot. Cable FC 2391 (PN 41H9082) is available for this adapter.
Note: Total cable length to the attaching device is limited to 100 m and is for indoor use, only.

2-Port 10/100-Mbps CPCI Ethernet Adapter (FC 3111, PN 85H4735)

Provides two ports for either 10-Mbps or 100-Mbps Ethernet connections using RJ-45 connectors. These attachments provide:

2-KB entry hardware Transparent Bridging
IEEE 802.3 10-Mbps Ethernet
IEEE 802.3u 100-Mbps Ethernet

This adapter plugs into any 3U CPCI adapter slot. Cable FC 2391 (PN 41H9082) is available for this adapter.

T1/J1 24 Channel Digital Modem Adapter (FC 3201, PN 85H8812)

This adapter provides:

Support for T1/J1 line speed of 1.544 Mbps
Twenty-three 64-Kbps B-channels for data and one 64-Kbps D-channel for signaling, or twenty-four 64-Kbps time slots (24 DS0s) for channelized service
Selectable framing to D4 format for channelized and CAS support
Selectable framing to ESF for ISDN channelized, CAS, and switch support
Detection and generation of yellow and blue alarms
Facility Data Link (FDL) support
Generation of DSX-1 and CSU line build outs
Generation and detection of CSU loop codes
Line error counters for BPV, CV, CRC6, and framing-bit errors
Monitoring and enforcing of ANSI ones density requirement
B8ZI and AMI line coding
RJ-45 female connector
Support for cables FC 2326 (PN 30L6571) and for Japan FC 2328 (PN 30L6573).
Note: The cable you receive with your T1/J1 Digital Modem Adapter is required for Electromagnetic Compatibility (EMC) compliance.

This adapter plugs into any 6U CPCI adapter slot.

T1/J1 12-Channel Digital Modem Adapter (FC 3202, PN 35H2262)

This adapter provides:

Support for T1/J1 line speed of 1.544 Mbps
Twenty-three 64-Kbps B-channels for data and one 64-Kbps D-channel for signaling, or twenty-four 64-Kbps time slots (24 DS0s) for channelized service
Selectable framing to D4 format for channelized and CAS support
Selectable framing to ESF for ISDN channelized, CAS, and switch support
Detection and generation of yellow and blue alarms
Facility Data Link (FDL) support
Generation of DSX-1 and CSU line build outs
Generation and detection of CSU loop codes
Line error counters for BPV, CV, CRC6, and framing-bit errors
Monitoring and enforcing of ANSI ones density requirement
B8ZI and AMI line coding
RJ-45 female connector
Support for cables FC 2326 (PN 30L6571) and for Japan FC 2328 (PN 30L6573).
Note: The cable you receive with your T1/J1 Digital Modem Adapter is required for Electromagnetic Compatibility (EMC) compliance.

This adapter plugs into any 6U CPCI adapter slot.

E1 30-Channel Digital Modem Adapter (FC 3204, PN 25L5606)

This adapter provides:

Support for E1 line speed of 2.048 Mbps.
Thirty 64-Kbps B-channels for data and one 64-Kbps D-channel for signaling or thirty-one 64-Kbps time slots (31 DS0s) for channelized service.
Selectable framing to FAS and CRC4 formats.
Detection and generation of remote and AIS alarms.
Generation of line build outs for a 120-ohm line.
Two separate loopbacks for testing: payload and line. The diagnostics program provides a local loopback, as well.
Line error counters for bipolar and code violations, CRC4 code word errors, FAS errors, and E-bits.
B8ZI, AMI, and HDB3 line encoding.
RJ-45 female connector.
Support for cable FC 2327 (PN 30L6572).
Note: The cable you receive with your E1 Digital Modem Adapter is required for Electromagnetic Compatibility (EMC) compliance.

This adapter plugs into any 6U CPCI adapter slot.

E1 12-Channel Digital Modem Adapter (FC 3205, PN 35L2263)

This adapter provides:

Support for E1 line speed of 2.048 Mbps.
Thirty 64-Kbps B-channels for data and one 64-Kbps D-channel for signaling or thirty-one 64-Kbps time slots (31 DS0s) for channelized service.
Selectable framing to FAS and CRC4 formats.
Detection and generation of remote and AIS alarms.
Generation of line build outs for a 120-ohm line.
Two separate loopbacks for testing: payload and line. The diagnostics program provides a local loopback, as well.
Line error counters for bipolar and code violations, CRC4 code word errors, FAS errors, and E-bits.
B8ZI, AMI, and HDB3 line encoding.
RJ-45 female connector.
Support for cable FC 2327 (PN 30L6572).
Note: The cable you receive with your E1 Digital Modem Adapter is required for Electromagnetic Compatibility (EMC) compliance.

This adapter plugs into any 6U CPCI adapter slot.

2-Port Analog FXS Voice/Fax CPCI (FC 3210, PN 85H8828)

Provides two ports that allow attachment of analog telephone handset or analog fax machine to the IBM 2212.

This adapter plugs into any 3U CPCI adapter slot.

2-Port Analog FXO Voice/Fax CPCI (FC 3211, PN 02L2398)

Provides two analog voice ports that allow attachment to analog central office trunks.

This adapter plugs into any 3U CPCI adapter slot.

2-Port Analog E&M Voice/Fax CPCI (FC 3212, PN 02L2400)

Provides two analog voice ports that provide analog PBX emulation for attachment to private networks.

This adapter plugs into any 3U CPCI adapter slot.

4-Port Analog 56K Modem CPCI (FC 3213, PN 85H8830)

This adapter allows up to four analog phone line connections. The modems support the V.34 standard up to 33.6 Kbps as well as K56Flex technology and the new V.90 ITU standard for speeds up to 56 Kbps. Transmit rates are limited to a maximum of 33.6 Kbps. Only asynchronous protocols, that is, dial-up PPP, are supported.

The external interface for each modem is a RJ-11 connector.

This adapter plugs into any 3U CPCI adapter slot.

Compression/Encryption CPCI Adapter (FC 3215, PN 85H4732)

Provides a coprocessor with dedicated memory. When the software begins to perform compression and encryption functions it uses the coprocessor's memory to prevent a decline in performance. After you install and enable this compression/encryption adapter in the IBM 2212 the AIS software uses the coprocessor for compression and encryption packet processing. This adapter provides:

CDMF, DES, Triple-DES, RC4 encryption support

Note:

Encryption support is controlled by the AIS software and is subject to export control. Before the compression/encryption adapter can be used for data encryption you must download the version of the AIS software with data encryption support. You can obtain this software at:

http://www.networking.ibm.com/support/downloads/2212

LZS, and MPPC compression support
127/63 simultaneous full-duplex LZS/MPPC compression sessions

This adapter plugs into any 3U CPCI adapter slot.

Footnotes:

⁵: When speeds above 2.048 Mbps are used, only port number 1 on an adapter can be clocked at this rate. Ports 2, 3, and 4 must be running at 64 Kbps or less.

[ Top of Page | Previous Page | Next Page | Table of Contents | Index ]

CPCI adapter options
4-Port WAN CPCI	3103	85H8836	"4-Port WAN CPCI Adapter (FC 3103, PN 85H8836)"
2-Port ISDN BRI-U CPCI	3104	85H4725	"2-Port ISDN BRI-U CPCI Adapter (FC 3104, PN 85H4725)"
2-Port ISDN BRI-S/T CPCI	3105	85H4726	"2-Port ISDN BRI-S/T CPCI Adapter (FC 3105, PN 85H4726)"
1-Port ISDN PRI T1/J1 CPCI	3106	85H4727	"1-Port ISDN PRI (T1/J1) CPCI Adapter (FC 3106, PN 85H4727)"
1-Port ISDN PRI E1 CPCI	3107	85H4728	"1-Port ISDN PRI (E1) CPCI Adapter (FC 3107, PN 85H4728)"
2-Port ISDN PRI T1/J1 CPCI	3108	85H4680	"2-Port ISDN PRI T1/J1 CPCI Adapter (FC 3108, PN 85H4680)"
2-Port ISDN PRI E1 CPCI	3109	85H4682	"2-Port ISDN PRI E1 CPCI Adapter (FC 3109, PN 85H4682)"
2-Port Token-Ring CPCI	3110	85H4717	"2-Port Token-Ring CPCI Adapter (FC 3110, PN 85H4717)"
2-Port 10/100 Ethernet CPCI	3111	85H4735	"2-Port 10/100-Mbps CPCI Ethernet Adapter (FC 3111, PN 85H4735)"
2-Port Analog FXS Voice/Fax CPCI	3210	85H8828	"2-Port Analog FXS Voice/Fax CPCI (FC 3210, PN 85H8828)"
2-Port Analog FXO Voice/Fax CPCI	3211	02L2398	"2-Port Analog FXO Voice/Fax CPCI (FC 3211, PN 02L2398)"
2-Port Analog E&M Voice/Fax CPCI	3212	02L2400	"2-Port Analog E&M Voice/Fax CPCI (FC 3212, PN 02L2400)"
4-Port Analog 56K Modem CPCI	3213	85H8831	"4-Port Analog 56K Modem CPCI (FC 3213, PN 85H8830)"
Compression/Encryption CPCI Adapter	3215	85H4732	"Compression/Encryption CPCI Adapter (FC 3215, PN 85H4732)"

CPCI adapter options available for Models 4xx only:
T1/J1 24-channel Digital Modem Adapter	3201	85H8812	"T1/J1 24 Channel Digital Modem Adapter (FC 3201, PN 85H8812)"
T1/J1 12-channel Digital Modem Adapter	3202	35H2262	"T1/J1 12-Channel Digital Modem Adapter (FC 3202, PN 35H2262)"
E1 30-channel Digital Modem Adapter	3204	25L5606	"E1 30-Channel Digital Modem Adapter (FC 3204, PN 25L5606)"
E1 12-channel Digital Modem Adapter	3205	35L2263	"E1 12-Channel Digital Modem Adapter (FC 3205, PN 35L2263)"